Thrall wordmark

Thrall · Automatic Gain Rider

Ride the take, not the transient.

Slow automatic gain rider for long-term vocal and bass level stability. Thrall is an automatic gain rider in design at KRIG Audio. It will follow slow, phrase-level changes in loudness and correct them with gentle gain moves, leaving fast transients to your compressor and your hands. It is built for Windows and macOS, for beginners who want a clear starting point and for engineers who want to set the window, range and silence rules themselves.

Planned15 of 15Built for Windows and macOS

Thrall will measure a longer-term average or perceived level across a chosen window and slowly raise or lower gain toward a target, within a maximum boost and cut you set. It is not meant to react to individual peaks; it is meant to make the phrase sit at a consistent level before a compressor or limiter does its work. Silence handling, hold and recovery are part of the design so that pauses and breaths are not pulled up into noise, and the applied gain is shown separately from the gain the detector thinks is required.

Not released. No build exists yet.

What is Thrall for?

You have tracked a harsh vocalist who leans back on the low screams and steps into the high ones, and the raw take swings several dB across a verse. Clip gain edits and volume automation would fix it, but you have six songs and a deadline, and every manual node is another thing to recall later. A fast compressor set to catch those swings will also flatten the attack of every consonant and make the vocal sound sat on before it even reaches your mix chain.

What it does

Thrall will measure a longer-term average or perceived level across a chosen window and slowly raise or lower gain toward a target, within a maximum boost and cut you set. It is not meant to react to individual peaks; it is meant to make the phrase sit at a consistent level before a compressor or limiter does its work. Silence handling, hold and recovery are part of the design so that pauses and breaths are not pulled up into noise, and the applied gain is shown separately from the gain the detector thinks is required.

What it doesn’t do

  • It is not a compressor, gate or limiter, and it does not replace fast dynamic control.
  • It does not write automation data into your DAW by itself.
  • It does not make a badly performed take sound performed, and it is not a de-esser or EQ.
  • It is not a mastering loudness normaliser and does not guarantee a target LUFS reading.

The design.

Controls and displays as currently designed. They can change before any build exists.

01 / 04

Controls that matter

The control set starts with Target Level, expressed in a unit the DSP contract will define, most likely dBFS RMS or LUFS once the detector is settled. Ride Speed or Response sets how quickly the rider is allowed to move, and Max Boost and Max Cut set the hard limits so the rider can never rescue or destroy a take beyond what you allow. Silence Threshold, Hold and Recovery govern what happens in pauses and between phrases.

Detector Filtering lets the rider ignore rumble or focus on the vocal band, and Mix or Output lets you compare against the untreated signal at matched level. Bypass and an Audition or Freeze function let you check the gain envelope without committing to it.

  • Target Level, Ride Speed, Max Boost and Max Cut are the core four.
  • Silence Threshold, Hold and Recovery protect pauses and breaths.
02 / 04

The rider display

Required gain and applied gain are shown as separate traces so you can see when the rider wants to move further than your limits allow. Positive and negative gain are both shown with sign and unit, because a rider that only displays reduction is hiding half of what it does.

A status area is planned for silence and hold states, so you can tell the difference between a quiet passage the rider is respecting and a passage it is incorrectly boosting. The display is a design concept.

  • Input history, target line and applied gain are separate layers.
  • Required gain versus applied gain shows when limits are active.
  • Silence and hold states must be visible, not implied.
03 / 04

Meters and units

Thrall will show level in a defined unit, gain in dB with sign, and time in seconds or milliseconds where timing controls exist. The rider is not a compressor, so the gain display is not labelled as gain reduction; it shows both boost and cut. If a loudness-style unit is used for the target, the standard and window will be stated in the interface and in the documentation.

The meters must mean what they display. We will not animate a meter on a timer and present it as signal.

  • Gain is shown in dB with sign, not as compressor-style reduction.
04 / 04

Where it sits in a chain

The intended place is early in the vocal or bass chain, before compression and tonal shaping, so the compressor receives a more consistent input and works less. On a vocal, that means after any cleanup gate and before EQ, compression and saturation. On a bass DI, it means before the amp or saturation stage so the character processing sees a stable level.

It can also sit before a bus compressor on a lead instrument or a narration track, where long-term level changes are the problem and transient shaping is not. It is not intended as a final loudness stage, and it should not be used to fix a mix that has no dynamic control further down the chain.

  • Place it before compression and saturation, not after the limiter.
  • Use it on vocals, bass DI, lead instruments and narration.
  • It prepares material for dynamics; it does not replace them.

Three ways to use it

Step-by-step starting points from real heavy sessions. Every mix is different; trust your ears over any recipe.

Harsh vocal phrase levelling
  1. Insert Thrall first on the vocal chain, before EQ and compression.
  2. Set Target Level from the average of a verse you consider well performed.
  3. Set Ride Speed slow enough that individual words are not pulled around.
  4. Limit Max Boost and Max Cut to a range you would accept from a human fader rider.
  5. Check the applied gain trace across the whole take, then bypass and compare at matched level.
Bass DI macro stability
  1. Place Thrall after the DI cleanup and before the amp or saturation stage.
  2. Set the detector filtering so the rider follows the bass fundamental range, not string noise.
  3. Use a slower response and a modest Max Cut so note-to-note movement stays musical.
  4. Watch the silence and hold states during rests so the rider does not lift noise.
  5. Print or commit the result only after checking the whole song, not one riff.
Pre-compressor preparation on a lead
  1. Insert Thrall before the lead bus compressor.
  2. Set a target that represents the level you want the compressor to see.
  3. Keep Max Boost conservative so quiet intentional phrases are not flattened upward.
  4. Compare required gain against applied gain to see where your limits are working.
  5. Then set the compressor normally, with less range needed than before.

Before you reach for it

The mistakes we see most often with this kind of tool.

Common mistakes

  • Setting Ride Speed fast enough that Thrall behaves like a compressor and flattens the performance.
  • Leaving Max Boost wide open so quiet, intentional phrases are pulled up to the target.
  • Using Thrall to fix a take that needs editing, comping or a retake.

Factory presets

Correct longer-term level changes without replacing a compressor. The factory library runs to dozens of presets, often more than a hundred, covering technical jobs, genres and instrument categories, sorted by category and searchable. Three of them are below.

Harsh Vocal Level Riding

Target Level set to the average of the vocal, with a medium Ride Speed and limits on Max Boost and Max Cut. Silence Threshold and Hold keep breaths and pauses from being pushed up.

Bass Performance Riding

Slow Ride Speed, so it follows notes and phrases and leaves single transients alone. It evens out the performance before any compressor sees it.

Lead Guitar Phrase Balance

Moderate Ride Speed with more Max Boost than Max Cut. Quiet phrases come up to the target, and Recovery keeps the move from being heard between phrases.

Preset families: Harsh Vocals, Clean Vocals, Backing Vocals, Bass, Lead Instruments, Spoken Voice and General Level Riding.

Why KRIG Audio

Before KRIG we spent years mixing with other makers’ plugins, and we learned what a heavy session needs from a tool. So every plugin starts with the sound: DSP written to a measured target and tested until it behaves the same way every time.

  • Built from years at the deskWe mixed and mastered with plugins from many makers for years, on our own records and on other people’s, and the same problems kept costing us time: gates that chatter, saturation that smears a riff, limiters that flatten the kick. Each KRIG plugin starts from one of those problems.
  • DSP written to a measured targetWe write our own signal processing. Before the first line of code we decide what the plugin must do to the signal: the curve it draws, the harmonics it adds, the noise it must not. The DSP is measured against that target, and when the two disagree, the code goes back.
  • Tested again and againSine tones, sweeps, impulses and noise at the levels people mix at. Every control swept while audio plays, to catch clicks and zipper noise. Every sample rate and buffer size a session can run at. Then real multitracks, at matched level, judged by ear. Every new build runs it all again.
  • Meters that tell the truthEvery meter and display is fed signals whose values we already know, and has to show exactly that. A VU reads like a VU, gain reduction reads gain reduction, and nothing on the screen moves for show, so what you see is what the plugin is doing to your track.
  • Presets for every jobDozens of factory presets per plugin, many with more than a hundred: technical fixes, genre starting points and instrument categories, sorted and searchable. A beginner starts from the job in front of them; an engineer gets a tested reference to build on.
  • Buy once, keep itEvery KRIG plugin is a one-time purchase with a perpetual licence, never a subscription. A 14-day full-feature trial is planned, so you can judge each plugin in your own sessions before you pay.

Not sure it’s the right tool?

How Thrall differs from its closest KRIG neighbours.

  • Shackle · Shackle is a stereo compressor for fast and medium dynamics, while Thrall is a slow rider for long-term level changes.
  • Nihil · Nihil gates and expands to control bleed and silence, while Thrall rides overall level and does not gate.
  • Entomb · Entomb clips and limits peaks for headroom, while Thrall corrects average level before dynamics processing.

Where Thrall stands

Thrall is planned. No build exists yet, and the design can still change. There are no release dates until a plugin is ready. Follow the roadmap

  1. Research & specificationPlanned
  2. Interface designPlanned
  3. DSP implementationPlanned
  4. Validation & QAPlanned
  5. Release preparationPlanned
  6. ReleasedPlanned

Details

What we can state today. System requirements, tested hosts and test results are published here before release.

Type
Automatic Gain Rider
Status
Planned
Platforms
Built for Windows and macOS
Formats (planned)
VST3 for Windows and macOS, AU for macOS. No AAX
Presets
Factory library, see above
Made for
Beginners to mastering engineers
Licence (planned)
Perpetual, one-time purchase. Computers and updates confirmed when the plugins are finished
Trial (planned)
14-day full-feature trial

Thrall questions

It is not a compressor, gate, limiter or de-esser, and it does not write automation into your DAW. It is a slow gain rider intended to stabilise long-term level before other dynamics processing.

Yes. A clear target, a slow default response and conservative boost and cut limits should give a usable starting point, while the deeper controls remain available for engineers who want to set the window and silence rules themselves.

KRIG plugins are being built for Windows and macOS.

Shackle is a stereo compressor that reacts to dynamics on a musical timescale. Thrall moves slowly toward a target level over phrases and sections, and it is not meant to shape attack or punch.

It can reduce the amount of manual work on long-term level changes, but it does not replace artistic automation. Rides that follow a word, a breath or a deliberate dynamic move are still your decision.

Next on the roadmap

Nihil

Gate / Expander

Nihil wordmark