Legion wordmark

Legion · Stereo Width & Mid/Side

Shape the stereo field, protect the centre.

Stereo width and Mid/Side control that keeps the centre under control. Legion is a stereo width and Mid/Side shaping plugin for dense metal mixes where wide guitars, room mics and doubled parts can swallow the vocal, snare and kick. It is still in design, so this page describes how it will work. It will give you a stereo tool that shows the real relationships between L/R and Mid/Side instead of decorative width.

Planned13 of 15Built for Windows and macOS

Legion is built around a stereo L/R to Mid/Side matrix. It separates the centre (Mid) content from the side (Side) content, lets you change the relative amount of each, and recombines them back to stereo. Width changes the M/S relationship, M/S Balance shifts energy between centre and sides, Side Trim controls the side component independently, and Center Focus lets you protect or emphasise the mono-critical centre. A Mono Bass stage will fold low frequencies to mono below a chosen frequency. Because every width move changes phase and correlation relationships, Legion is designed to show you the real cost of the width you are adding, not just a wider-looking picture.

Not released. No build exists yet.

What is Legion for?

You have two rhythm guitar tracks panned hard left and right, a room pair on the drums and a doubled backing vocal, and the mix sounds impressively wide in the control room. Then you check it in mono and the vocal drops back, the snare loses its centre, and the kick and bass feel weaker because the low end was spread across the sides. Widening further makes it worse, and a plain mono fold-down does not tell you which part of the width is actually costing you the centre.

What it does

Legion is built around a stereo L/R to Mid/Side matrix. It separates the centre (Mid) content from the side (Side) content, lets you change the relative amount of each, and recombines them back to stereo. Width changes the M/S relationship, M/S Balance shifts energy between centre and sides, Side Trim controls the side component independently, and Center Focus lets you protect or emphasise the mono-critical centre. A Mono Bass stage will fold low frequencies to mono below a chosen frequency. Because every width move changes phase and correlation relationships, Legion is designed to show you the real cost of the width you are adding, not just a wider-looking picture.

What it doesn’t do

  • It is not a 3D imaging, psychoacoustic enhancement or auto-width plugin; it does not generate new stereo content that was not in the source.
  • It is not a metering suite: correlation and goniometer displays are part of the stereo tool, not a replacement for a dedicated measurement plugin.
  • It does not guarantee mono compatibility; it shows you the relationships so you can decide, and every width setting still needs a mono check.

The design.

Controls and displays as currently designed. They can change before any build exists.

01 / 05

Width and M/S balance

The core of Legion is a stereo matrix: the L/R input is split into Mid and Side, the relative amounts are adjusted, and the result is folded back to stereo. Width is the main control and moves the side content relative to the mid content, so pulling width back tightens the image toward the centre and pushing it forward spreads the sides. M/S Balance is a separate control that shifts energy between the centre and the sides without simply scaling the whole image.

Width and M/S Balance do different jobs and are labelled as such, so a producer can tighten a wide guitar pair with Width while leaving the centre weight of the snare and vocal intact, or push the sides for an ambient section and then check what it cost in mono.

  • Width controls the relative Side content against Mid.
  • M/S Balance shifts energy between centre and sides.
  • Every width move is checked against correlation, not just heard as wider.
02 / 05

Centre protection and Side Trim

Side Trim is an independent level control for the side component, so you can reduce the sides without touching the centre, or trim them up for a specific section. Center Focus protects the mono-critical centre: the vocal, snare and kick information that must survive a mono fold-down. Its exact behaviour is still being designed.

Mono Bass is a frequency-dependent stage that folds content below a chosen frequency to mono. This is not a simple width control: it needs a validated crossover and phase behaviour, and it is labelled as frequency-dependent processing. Until it is built and measured, treat Mono Bass as a planned feature, not a guarantee that your low end will translate.

  • Side Trim adjusts the side component independently of the centre.
  • Center Focus protects mono-critical centre content.
  • Mono Bass is frequency-dependent and requires its own validation.
03 / 05

Mono audition and correlation

Mono Audition is a monitoring function that folds the output to mono so you can hear what the width is costing you without changing the rendered audio. Correlation monitoring shows the relationship between left and right channels as a real display, not a decorative animation. The correlation meter will show actual signal relationships, and the mono preview is clearly a monitor state, not a processing state.

These displays only mean something when they are fed by real signal. On a built plugin they must be driven by the actual signal tap, with defined ballistics and units, or they should not be shown at all.

  • Mono Audition is a monitor fold-down, not a render change.
  • The correlation display shows real L/R relationships.
  • No meter animation without a real signal tap.
04 / 05

Output, bypass and A/B

Output is a clean level control after the matrix so you can level-match a width change before judging it. Bypass is a true bypass of the processing path, and A/B lets you compare two states of the same session without losing your place.

Bypass should not leave a hidden gain change, and A/B should not silently reset the matrix. Host recall, automation and state restore are tested separately and are not claimed yet.

  • Output for level-matched comparison.
  • True bypass of the processing path.
  • A/B comparison without losing state.
05 / 05

The interface

The UI centres on a stereo field display: a vector or goniometer view of the actual stereo relationships, a correlation meter, and separated L/R and M/S level displays so you can see how much energy sits in the centre versus the sides. The Width, M/S Balance, Side Trim and Center Focus controls sit around that display, with Mono Bass frequency and Mono Audition clearly grouped as separate functions. The industrial housing follows the KRIG visual language, with patina on the case only and clean, readable scales.

The display must show real relationships, not a decorative wide field. Nothing in the UI should imply a measurement that is not actually being made.

  • Stereo field vector and correlation meter.
  • Separated L/R and M/S level displays.
  • Concept displays are marked as concept until real signal exists.

Three ways to use it

Step-by-step starting points from real heavy sessions. Every mix is different; trust your ears over any recipe.

Wide rhythm guitar pair that survives mono
  1. Set Width to a moderate value and check the correlation meter before pushing further.
  2. Use Side Trim to reduce the side content if the pair is masking the vocal or snare centre.
  3. Engage Mono Audition and confirm the vocal and snare still hold their place.
  4. If the low end weakens in mono, try the Mono Bass stage at a low frequency and re-check.
  5. Level-match with Output before deciding whether the width change is actually better.
Drum room and overhead field control
  1. Start with Width near neutral and listen to the room pair in context with the close mics.
  2. Pull Width back slightly to tighten the room image if it is blurring the snare centre.
  3. Use M/S Balance to shift energy toward the centre if the kit feels disconnected.
  4. Check correlation and mono audition to confirm the kick and snare stay centred.
  5. Compare A/B against the unprocessed room to make sure the tighter image still has depth.
Mix bus stereo check before export
  1. Insert Legion on the mix bus with Width neutral and confirm the correlation reading.
  2. Make a small Width reduction if the mix is overly side-heavy and the centre feels weak.
  3. Use Mono Audition to hear the fold-down and note what moves or disappears.
  4. Apply the Mono Bass stage only if the low end is genuinely spread and re-check mono.
  5. Bypass and A/B against the original to confirm the change is an improvement, not just different.

Before you reach for it

The mistakes we see most often with this kind of tool, and where it usually sits in a chain.

Common mistakes

  • Pushing Width up because the mix sounds wider in stereo, without checking correlation and mono, so the centre quietly loses the vocal and snare.
  • Using Mono Bass as a fix for a low end that was never properly balanced, instead of fixing the kick and bass relationship first.
  • Judging a width change without level-matching with Output, so a louder side image is mistaken for a better one.

Where it fits

Legion is intended for the point in the chain where stereo placement is decided, not where tone is shaped. On a guitar bus it would sit after tone and dynamics processing and before bus compression, so the width decision is made on the shaped signal. On a drum bus it would sit after close-mic and room balancing and before glue compression. On the mix bus it would sit late, after tonal and dynamic processing, as a final stereo check before peak control. These are illustrative positions; the right place depends on the session, and every width move still needs a mono check.

Factory presets

Manage stereo width, balance and mono compatibility without destabilising the mix. The factory library runs to dozens of presets, often more than a hundred, covering technical jobs, genres and instrument categories, sorted by category and searchable. Three of them are below.

Wide Rhythm Guitar Bus

Width raised a little on the bus of two hard-panned guitars, with Side Trim holding the sides in check. Watch correlation while you set it.

Mono-Compatible Low End

Mono Bass collapses the lows to the centre below its frequency, and Center Focus protects kick and bass. The low end then holds up on a mono system.

Mix Bus Width Review

Width at unity with Mono Audition and the correlation readout up front. A setup for judging the stereo image before deciding to change anything.

Preset families: Overheads, Guitars, Synths, Ambient Instruments, Buses, Stereo Correction and Mix Bus.

Why KRIG Audio

Before KRIG we spent years mixing with other makers’ plugins, and we learned what a heavy session needs from a tool. So every plugin starts with the sound: DSP written to a measured target and tested until it behaves the same way every time.

  • Built from years at the deskWe mixed and mastered with plugins from many makers for years, on our own records and on other people’s, and the same problems kept costing us time: gates that chatter, saturation that smears a riff, limiters that flatten the kick. Each KRIG plugin starts from one of those problems.
  • DSP written to a measured targetWe write our own signal processing. Before the first line of code we decide what the plugin must do to the signal: the curve it draws, the harmonics it adds, the noise it must not. The DSP is measured against that target, and when the two disagree, the code goes back.
  • Tested again and againSine tones, sweeps, impulses and noise at the levels people mix at. Every control swept while audio plays, to catch clicks and zipper noise. Every sample rate and buffer size a session can run at. Then real multitracks, at matched level, judged by ear. Every new build runs it all again.
  • Meters that tell the truthEvery meter and display is fed signals whose values we already know, and has to show exactly that. A VU reads like a VU, gain reduction reads gain reduction, and nothing on the screen moves for show, so what you see is what the plugin is doing to your track.
  • Presets for every jobDozens of factory presets per plugin, many with more than a hundred: technical fixes, genre starting points and instrument categories, sorted and searchable. A beginner starts from the job in front of them; an engineer gets a tested reference to build on.
  • Buy once, keep itEvery KRIG plugin is a one-time purchase with a perpetual licence, never a subscription. A 14-day full-feature trial is planned, so you can judge each plugin in your own sessions before you pay.

Not sure it’s the right tool?

How Legion differs from its closest KRIG neighbours.

  • Scry · Scry is measurement-only and tells you what the stereo and level relationships are; Legion is the tool that changes them.
  • Hollow · Hollow uses an external key signal to duck specific frequency conflicts between two sources; Legion shapes the stereo field of one signal.
  • Sigil · Sigil shapes tone with EQ bands; Legion shapes the Mid/Side relationship and does not replace tonal EQ.

Where Legion stands

Legion is planned. No build exists yet, and the design can still change. There are no release dates until a plugin is ready. Follow the roadmap

  1. Research & specificationPlanned
  2. Interface designPlanned
  3. DSP implementationPlanned
  4. Validation & QAPlanned
  5. Release preparationPlanned
  6. ReleasedPlanned

Details

What we can state today. System requirements, tested hosts and test results are published here before release.

Type
Stereo Width & Mid/Side
Status
Planned
Platforms
Built for Windows and macOS
Formats (planned)
VST3 for Windows and macOS, AU for macOS. No AAX
Presets
Factory library, see above
Made for
Beginners to mastering engineers
Licence (planned)
Perpetual, one-time purchase. Computers and updates confirmed when the plugins are finished
Trial (planned)
14-day full-feature trial

Legion questions

It is not a 3D imaging or psychoacoustic enhancement plugin, it does not create stereo content that is not in the source, and it is not a metering suite.

Yes. Clear defaults and a neutral starting point, with the correlation and mono displays giving immediate feedback. The deeper M/S controls are there for engineers who want them, but a beginner can make a safe width decision and hear the mono cost before committing.

KRIG plugins are being built for Windows and macOS. Nothing is available to download.

Scry is measurement-only: it shows peaks, loudness, correlation and stereo relationships without changing the audio. Legion is the shaping tool that changes the stereo and Mid/Side relationships. They are complementary: you would use Scry to see what is happening and Legion to act on it.

No. Legion is designed to show you the real relationships and give you a mono audition so you can judge the cost of a width move, but no width setting guarantees mono compatibility. Every change still needs a mono check in context.

Next on the roadmap

Hollow

Spectral Sidechain Ducking

Hollow wordmark